خمیر سیلیکون 60 گرمی مارک Kafuter مدل K-5211
قیمت اصلی 79,000 تومان بود.67,000 تومانقیمت فعلی 67,000 تومان است.
تخفیف : 12,000 تومان
( آخرین بروزرسانی : 17 اردیبهشت, 1403 )
ویژگی های کلیدی محصول
- مارک: Kafuter
- مدل: K-5211
- وزن: 60 گرم
بررسی اجمالی محصول
خمیر سیلیکون 60 گرمی تاریخ تولید 2022/10
از خمیر سیلیکون برای انتقال حرارت بین دو قطعه فلزی استفاده میشود.
نقد و بررسی : خمیر سیلیکون 60 گرمی مارک Kafuter مدل K-5211
از خمیر سیلیکون برای انتقال حرارت بین دو قطعه فلزی استفاده میشود.
وقتی میخواهید چیپ ال ای دی رو به هیت سینک متصل کنید، برای اینکه وسطش هوا نمونه و تمامی قسمت های پی سی بی آلومینیومی چیپ به هیت سینک بچسبه، باید از خمیر سیلیکون استفاده کنید.
چون هوا رسانای ضعیف گرماس و اگه وسطش هوا بمونه باعث میشه حرارت به درستی انتقال پیدا نکنه و عمر چیپ کم بشه.
خمیر سیلیکون کافوتر یکی از با کیفیتترین خمیرهای بازاره و می تونید این محصول رو از فروشگاه اینترنتی آلفاکیت تهیه کنید.
Features:
K-5211 thermal grease is produced using imported raw materials and formulas.
It is made of a paste grease made from a combination of metal oxides and organosilicones with good thermal conductivity and insulation properties. Good electrical insulation, wide operating temperature (operating temperature -50°C~+200°C), good stability, lower consistency and good workability.
This product is non-toxic, non-corrosive, tasteless, dry, and insoluble.
Use:
Widely used in electronics, electrical appliances, components, heat dissipation, filling or coating, in order to derive the heat generated by components.
Such as CPU and heat sink interstitial, high-power transistor, thyristor components, diodes and substrate (aluminum, copper) in contact with the filling of the gap, as the machine power amplifier tube and heat sink, semiconductor refrigeration and so on.
Reduce the operating temperature of the heating element.
Exterior : White paste
Penetration (1/10mm, 25°C) : 260~300
Specific gravity (g/cm3) : 1.9 to 2.1
Oil Dispersion (%, 200°C, 8h) : ≤2.0
Volatile (%, 200°C, 8h) : ≤2.0
Breakdown voltage strength (kv/mm) : ≥10
Volume resistance (Ω.cm) : 4×1014
Thermal conductivity (w/m·k) : ≥1.2
Instructions:
The surface to be coated is cleaned, oil stains are removed, and the thermally conductive silicone ester is directly extruded to uniformly coat the surface to be coated. The coating method can be applied by brushing, squeegeeing or roller coating as required.
Precautions:
The construction surface should be uniform, and the more the coating is, the better the coating should be. Instead, a thin layer can be applied under the premise of ensuring the clearance of the filled surface.
دیدگاهی ثبت نشده.